How to wire an outside light to an indoor switch

Free Delivery on Eligible Orders! Choose wire that is rated for in-wall use. With the switch still away from the wall, reconnect the electrical supply and use the switch , taking care not to touch any metallic parts behind.

OK the new outside light should light up. The lantern may stay lit, but should switch off after a short time.

An outdoor light switch seems like a simple thing to install , but it is not as simple as it seems at the beginning. There is a lot to consider when you install and outdoor light switch. There are many factors to consider when installing one of these light switches. The information below will share with you some tips on how to properly go about installing an outdoor light switch. Summary: Wiring an exterior wall light : Learn how to wire an exterior wall light , prepare a new lighting circuit, fit a boxed light fitting, fit a bracketed light fitting, install an inside switch , and fit an outside switch.

I have an outdoor security light wired into the house lighting circuit. I want a switch (situated indoors) to control whether the security light has power or not.

I cut the wire coming from the security light to the light circuit and put a normal indoor light switch in. How do I wire a switch to a PIR light ? Is this the correct way to install an outside light The cable is chased vertically from the inside of the house (just under the plaster) then drilled though the wall. RCD protected circuit at the fuse board.

Outdoor lighting gives you loads of benefits. It can illuminate your path to the front door. Then put the Brown wire in the Lat the switch and cut a piece of wire and link the two com terminals together, making sure the red cable from the existing light goes to com.

Then connect the wires at the light , ensuring all the earths are connected. I want to replace the outside light switch with one that turns lights Off and On automatically. The existing switch has a copper wire connected to the switch frame. One way lighting circuit using in-line switching. Line diagram of a one way lighting circuit using in line method (fig 1).

A one way light switch is quite easy to wire up. The cable going to the light switch is connected as follows (fig 2). The red wire from the feed cable is connected to the top terminal, the red wire going to the light is connected to the bottom terminal, the black wires from both cables are connected together in a plastic terminal block and the earth.

Wire wall lights to a switch The switch cable runs from the junction box to the point where you wish to install your switch. Once you have the switch backplate fitted into the wall with the switch cable entering through the back of it, you need to connect the wires to your switch. Note the black insulated wire is the power supply, and the white insulated wire is the electrical system neutral wire. The bare copper wire that is connected to the light fixture itself is the electrical systems grounding wire. Examples include adding lighting underneath kitchen wall cabinets, where the existing switch will be at the exact height of the new lighting , or installing an outside light by routing the cable directly through the back of an existing switch box to the outside.

I have opened the switch up (obv after turning elec off!) and there are two wires coming in to the switch. He is correct to wire a switch in to the circuit anyway so that you can switch the PIR and light off for maintenance, also, if the sparky is doing a rewire he should consider putting the outside lighting on a separate circuit on its own fused way in the consumer unit. Low Prices on Light Switch With Timer. What You Will Need Wire an Outside Light to an Existing Switch Well, to start with, you need to have some basic working knowledge of how a switch works and is wired. You also need to know all the basic safety tips with regard to handling naked electric wires.

Wiring an outside flood light is simple yet the mounting takes time. To install and wire an outside light. First locate the power source you are going to use.

A simple lighting circuit is where the light switch is installed between the supply and the light fitting. This may be a junction box in the garage that is used for other outlets or lights. I have an existing outdoor security light that is operated by a mains light switch inside. So that the indoor light switch instead powers the outdoor festoon lights. The light can be switched independently of the main lights in the room which means it can serve as a night light above the be a reading light in the bedroom, a hall light which can be operated from somewhere other than the hall, an outside light , operated from indoors, a reading light in the lounge or, more commonly, a picture light in the lounge and dining room.

This is a wiring diagram for a motion sensor controlled shop light (LED) using a single pole, double throw, position switch. Using this wiring set up you can override the sensor to be off all the time, on all the time or controlled by the motion sensor. The sensor will be live no matter what position the switch is, but you can control the what the light does.